Dishlex dx 203 user manual

Close the door. Turn the program knob to set the washing program. Interrupting a washing program Refer to the chapter 'Washing programs'. Page 9: What To Do If tergents. Do not use abrasive products, scouring pads or solvents acetone etc. Internal cleaning Do an inspection at intervals of 3 months. Set a washing program for heavily soiled dishes. Use detergent, but do not put dishes in the appliance. Long periods of non-operation Do these steps when you do not use the appliance for a long period The appliance does not fill with water Open the water tap.

Technical data Dimensions Width mm Page Water Connection The drain hose can be lengthened using additional lengths and connectors. These must be purchased Caution! Always use new hoses when you from Electrolux Spare Parts. The extension length must connect the appliance to the water mains. Old not exceed 2 metres. Page 14 To the extent permitted by law, the lia- a claim under this warranty. Not enough water Inlet blockage.

Check for kinks and sharp bends in the inlet hose. Not enough water Dishlex Global series Water fill adjustment may be required if mains pressure has altered. Refer instruction sheet for fill time adjustment in instruction book. Not filling with water Check tap is on. Not filling, water is escaping down drain Drain hose is too low or not positioned correctly under bench top.

Refer to installation instructions. Not heating Incorrect program selection. Not heating enough Global series May not have reached correct temperature in given time. Models with a display rapidly flash an alarm code "nH". Refer to instruction book. Not operating - not commencing cycle No power. Check power turned on at power point. Not washing properly Top basket spray arm blocked or not rotating.

Temperature is not hot enough. Poor loading of dishes. Powder not dispensing properly Freshener in the way. Spray arm holes are blocked. Slow filling water. Taking too long to fill Poor water supply pressure or tap not turned on properly. Check tap is on. Soap not emptying Lid of detergent dispenser obstructed. Remove obstruction and continue cycle. Stuck in delay cycle Unit has been set in the delay cycle.

Press delay button until time is cleared. Unable to program Delay start could be set without user being aware. Refer to instruction book to clear. Vibrating Dishwasher not level. Adjust levelling legs as per installation instructions. Water being pumped out. Program not selected Inlet valve leaking water into machine, overflow pressure switch is energised and the drain pump turns on to pump out the water to a safe level.

Call 13 13 Water is not entering the dishwasher Check tap is on. Check Inlet hose filter sealing washer at tap. Water fills during dry cycle Westinghouse "J" series During dry cycle the inlet valve is opened for 15 seconds to allow 1 litre of water to pass through the syphon break to cool it down which assists in condensing the steam into water vapour fan assisted drying models only.

This is normal operation. Water not being pumped out Drain system blocked. Leaking at hose connections inlet and drain hoses. Check connections and hoses. Will not wash Wrong program is selected. Try other programs or refer to instruction book for program selection guide. Display window showing an 'upside down' 4 Unit has been set in the delay cycle. Flashing 7h Unit has been set into the delay start cycle. Press the delay button until time is cleared.

If both ok faulty inlet valve. Turn off tap and power to unit. Require service call, phone 13 13 Message in display May indicate a fault. PF Power interruption.

Program indicator light flashing. Westinghouse "J" series models with display window. Repeating single beep. Not filling. Check water supply and tap is turned on. Check inlet hose filter. Program times changing Dishlex "B" series The initial wash time shown in the digital display window models with display window may vary over time. The dishwasher adjusts the displayed wash time after each wash depending on the wash load and water conditions detected by 1 minute. Normal operation. Door gap uneven Dishwasher not level on the floor.

Adjust levelling legs as per installation manual. Door hitting left or right at top Dishwasher not level on the floor. Rocking dishwasher Dishwasher not level on the floor. Tilting forward Dishwasher not installed correctly. Tilting forward when both baskets out Dishwasher not installed correctly. Refer Installation Instructions.

Noise after program has finished Westinghouse "J" series Fan will continue to run to remove steam for approximately 20 minutes after the program has finished. Noisy during wash Chiller compartment too cold. Adjust chiller compartment temperature control. Noisy when filling with water Tap or valve whistling due to water pressure. Fit pressure reducing valve available from plumbing suppliers. Noisy when filling with water - banging noise Water hammer in the pipes when the water valve closes.

Not a product fault. Water pipes are moving in the wall. Fit anti hammer device, available from plumbing supplies and hardware stores or have a plumber fit a pressure reducing device. Walls are wet More prevalent when used overnight and left standing. Normal but check rinse aid is being used to help water "sheet off" the walls. Liner is stainless steel and will not rust.

Answer this question Send. About the Dishlex DX Dishlex DX specifications. Related product manuals. What do I do about a smelly dishwasher? In the case of a smelly dishwasher, you can take the following steps: - Clean the filters - Clean the spray arms - Clean the door rubbers - Run a hot wash program - Run an empty machine with a dishwasher cleaner.

Do you have to pre-rinse the dishes? It is not recommended to rinse dirty dishes before placing them in the dishwasher. For the life cycle of the machine, it is better to put everything dirty in the dishwasher. The grease on the dirty dishes is the lubrication for the pump in the machine.